Power Supply PS1000-A9-24.40

380 V AC to 480 V AC wide-range inputs
Output 24 V DC, 40 A, 960 W, 3-phase
Housing width 110 mm
Efficiency up to 95.3 %
Minimal inrush current surge
Shutdown input
Remote control for ON/OFF
DC OK relay contact
Current sharing for parallel use

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
お問い合わせ

注: Pepperl+Fuchs GmbH(旧社名)で発行された証明書・適合宣言書などすべての製品関連文書は、Pepperl+Fuchs AG(新社名)にそのまま適用されます。

データシート(PDF):

技術データ PS1000-A9-24.40

Electrical specifications
Efficiency		95.3 % at 3 x 400 V AC 95.2 % at 3 x 480 V AC
Power dissipation		47.3 W at 3 x 400 V AC 48.4 W at 3 x 480 V AC
Input
Voltage range		3x 380 ... 480 V AC (-15 %/+20 %), 50 ... 60 Hz (±6 %)
Current		1.65 A at 3 x 400 V AC 1.35 A at 3 x 480 V AC for lower output currents see technical information
Inrush current		4.5 A peak at 3 x 400 V AC, temperature-independent 4.5 A peak at 3 x 480 V AC , temperature-independent
Capacity factor		0.88 at 3 x 400 V AC 0.9 at 3 x 480 V AC
Remote control		terminals 15, 16 remote control for ON/OFF and shutdown input
Output
Rated voltage		24 V DC
Voltage range		24 ... 28 V DC factory setting: 24.1 V
Rated current		40 A
Current		continuous: 40 ... 34.3 A short-term up to 4 s: 60 ... 51.5 A linear power derating see technical information
Power		960 W
Ripple		max. 100 mV _pp
Hold-up time		25 ms at 3 x 400 V AC 25 ms at 3 x 480 V AC
Overload behavior		constant current mode
Short-circuit current		typ. 46 A continuous, load impedance < 10 mΩ
Voltage limitation		typ. 30.5 V DC max. 32 V DC
Fault indication output
Connection		terminals 13, 14
Output type		relay contact DC OK - contact is closed if the output voltage is > 90 % of the adjusted output voltage
Contact loading		max. 60 V DC/0.3 A ; 30 V DC/1 A ; 30 V AC/0.5 A resistive load min. 1 mA at 5 V DC
Galvanic isolation
Input/Output		SELV/PELV
Indicators/settings
Display elements		LED green: status DC OK - LED lights up if the output voltage is > 90 % of the adjusted output voltage LED red: overload - LED lights up if the output voltage is < 90 % of the adjusted output voltage or in case of short circuit - flashes if the shutdown has been activated or if the device has shut down due to overtemperature
Control elements		potentiometer , plug-in jumper
Configuration		setting of the output voltage via potentiometer setting of the operating mode - plug-in jumper plugged in: "parallel use" operating mode - plug-in jumper not plugged in: "single use" operating mode setting of the shutdown input: - plug-in jumper plugged in: device switches off
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4 , IEC/EN 61000-3-2 , IEC/EN 61000-3-3
Low voltage
	Directive 2014/35/EU	EN 61010-1
RoHS
	Directive 2011/65/EU (RoHS)	IEC/EN 63000:2019
Conformity
Degree of protection		EN 60529
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F) , see technical information
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		5 ... 95 %, noncondensing
Shock resistance		15 g , 6 ms or 10 g , 11 ms
Vibration resistance		2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 1 g
Mechanical specifications
Housing material		aluminum alloy , galvanized steel
Degree of protection		IP20
Connection
	Input	screw terminals conductor cross section: max. 6 mm² (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 1 Nm
	Output	screw terminals conductor cross section: max. 16 mm² (AWG 22-8) cable diameter: max. 5.2 mm, wire end ferrules included stripped insulation length: 12 mm tightening torque: max. 2.3 Nm
	Relay contact output	spring terminals conductor cross section: max. 1.5 mm² (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm
	Remote control/shutdown input	spring terminals conductor cross section: max. 1.5 mm² (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm
Mass		approx. 1500 g
Dimensions		110 x 124 x 127 mm (W x H x D) , without DIN mounting rail
	Height	124 mm
	Width	110 mm
	Depth	127 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
International approvals
UL approval		E223176
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27040790
ECLASS 12.0	27040790
ECLASS 11.0	27040790
ECLASS 10.0.1	27040790
ECLASS 9.0	27040790
ECLASS 8.0	27049090
ECLASS 5.1	27049090
ETIM 9.0	EC002542
ETIM 8.0	EC002542
ETIM 7.0	EC002542
ETIM 6.0	EC002542
ETIM 5.0	EC002542
UNSPSC 12.1	39121004

Details: PS1000-A9-24.40

Informative Literature: PS1000-A9-24.40

Literature	言語	ファイルタイプ	ファイルサイズ
Product Information - PS1000 for Global Use up to Zone 2/Div. 2	ENG	PDF	577 KB

Product Documentation: PS1000-A9-24.40

Product information	言語	ファイルタイプ	ファイルサイズ
Technical information	ENG	PDF	2915 KB
Safety and Security Documentation
Instruction manual / Betriebsanleitung	ALL	PDF	307 KB

Design / Simulation: PS1000-A9-24.40

CAD	言語	ファイルタイプ	ファイルサイズ
CAD 3-D / CAD 3-D	ALL	STP	10238 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	211 KB

Approvals: PS1000-A9-24.40

Certificates	認証番号	言語	ファイルタイプ	ファイルサイズ
DNV GL Marine	TAA0000316	ALL	PDF	179 KB
US CA UL	CoC E223176 RptRef E223176-20070416	ALL	PDF	444 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-4791	ALL	PDF	79 KB
EU Declaration of Conformity (P+F)	TDOC-4791AENG	ENG	PDF	177 KB