Ultrasonic sensor UC2000-30GM-IUEP-IO-V15-Y
- IO-Link interface for service and process data
- Programmable via DTM with PACTWARE
- Switch output and analog output
- Selectable sound lobe width
- Synchronization options
- Temperature compensation
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Stáhněte si kompletní katalogový list ve formátu PDF:
Výňatek z katalogového listu: Technická data UC2000-30GM-IUEP-IO-V15-Y
| Popis produktu |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 90 ... 2000 mm | |
| Adjustment range | 120 ... 2000 mm | |
| Dead band | 0 ... 90 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 200 kHz | |
| Response delay | minimum : 65 ms factory setting: 125 ms |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 100000 | |
| Indicators/operating means | ||
| LED green | solid: Power on flashing: Standby mode or IO link communication |
|
| LED yellow 1 | solid: Object in evaluation range flashing: Learning function, object detected |
|
| LED yellow 2 | solid: Object in evaluation range flashing: Learning function, object detected |
|
| LED red | solid red: Error red, flashing: program function, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS 15 ... 30 V voltage output |
|
| No-load supply current | ≤ 60 mA | |
| Power consumption | ≤ 1 W | |
| Time delay before availability | ≤ 120 ms | |
| Interface | ||
| Interface type | IO-Link | |
| Protocol | IO-Link V1.0 | |
| Transfer rate | Acyclical: typical 95 Bit/s | |
| Cycle time | min. 33.6 ms | |
| Mode | COM2 (38.4 kBit/s) | |
| Process data width | 16 bit | |
| SIO mode support | yes | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 4 V ... UB | |
| Input impedance | > 12 kΩ | |
| Output current | < 12 mA | |
| Pulse length | 0.5 ... 300 ms (level 1) | |
| Pulse interval | ≥ 33 ms (level 0) | |
| Synchronization frequency | ||
| Common mode operation | ≤ 30 Hz | |
| Multiplex operation | ≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ) |
|
| Output | ||
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA ... 20 mA or voltage output 0 V ... 10 V configurable |
|
| Rated operating current | 200 mA , short-circuit/overload protected | |
| Voltage drop | ≤ 2.5 V | |
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ 0.2 % of full-scale value | |
| Repeat accuracy | ≤ 0.1 % of full-scale value | |
| Switching frequency | ≤ 4 Hz | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable | |
| Load impedance | current output: ≤ 300 Ohm voltage output: ≥ 1000 Ohm |
|
| Temperature influence | ≤ 1.5 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation) |
|
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 5-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Stainless steel 1.4305 / AISI 303 TPU Polyamides |
|
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Mass | 72 g | |
| Dimensions | ||
| Length | 93 mm | |
| Diameter | 30 mm | |
| Factory settings | ||
| Output 1 | near switch point: 120 mm far switch point: 2000 mm Output mode: Window mode output behavior: NO contact |
|
| Output 2 | near limit: 120 mm far limit: 1000 mm Output mode: rising ramp output behavior: Current output 4 mA ... 20 mA |
|
| Beam width | wide | |
| General information | ||
| Note | nuts, M30 plastic | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC2000-30GM-IUEP-IO-V15-Y
Informative Literature: UC2000-30GM-IUEP-IO-V15-Y
| Literature | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|
| Application Report - Rugged Collision Protection for Cleaning Robots | ENG | 313 KB |
Product Documentation: UC2000-30GM-IUEP-IO-V15-Y
| Safety and Security Documentation | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|
| Návod k poużití | CZE | 147 KB |
Approvals: UC2000-30GM-IUEP-IO-V15-Y
| Certificates | Číslo certifikátu | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140156-4 / UL-CA-2133660-4 | ALL | 284 KB | |
| IO-Link Manufacturer Declaration | CERT-3037A | ALL | 140 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-5231A | ALL | 71 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-5570 | ALL | 64 KB | |
Související produkty: UC2000-30GM-IUEP-IO-V15-Y
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
Systém ultrazvukových senzorů USi-safety posouvá bezpečnostní aplikace na novou úroveň – ať již se jedná o aplikace v náročných, prašných prostředích nebo ve venkovních prostorách.
Společnost Pepperl+Fuchs vám nabízí různé dokumenty ke stažení, které obsahují poznatky o ultrazvukových senzorech.
Pepperl+Fuchs s.r.o.
Pod Vodárenskou věží 4
18208 Praha 8
Czech Republic
info@cz.pepperl-fuchs.com
+420 225 989 180
© 2024 Všechna práva vyhrazena
Pepperl+Fuchs je přední vývojář a výrobce průmyslových senzorů a komponentů pro světový trh automatizace. Neustálé inovace, trvalé kvalitní a stálý růst zaručuje mnoho úspěchů přes více než 70 let. Pepperl+Fuchs zaměstnává 6300 lidí po celém světě a má výrobní závody v Německu, USA, Singapuru, Maďarsku, Indonésii a Vietnamu, které podléhají ISO 9001.