Double sheet sensor UDCM-30GS-3EP1-IO-0,2M-V19
- Ultrasonic system for reliable detection of no, one, or two overlapping sheet materials, preferably sheet metal
- Insensitive to printing, colors, and shining surfaces
- Perpendicular or inclined sensor mounting relative to the sheet plane possible
- Integrated alignment aid
- IO-Link Interface for process data, parameterization and diagnosis
- Synchronization options
- No teach-in required
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Stáhněte si kompletní katalogový list ve formátu PDF:
Výňatek z katalogového listu: Technická data UDCM-30GS-3EP1-IO-0,2M-V19
| General specifications | ||
|---|---|---|
| Sensing range | 50 ... 150 mm , optimal distance: 80 mm | |
| Transducer frequency | approx. 85 kHz | |
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | indication: single sheet detected flashing (1 Hz) - standby mode flashing with short break (1 Hz) - IO-Link mode |
|
| LED yellow | indication: no sheet detected (Air) | |
| LED red | indication: double sheet detected flashing: device error |
|
| Electrical specifications | ||
| Operating voltage | 18 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 100 mA | |
| Power consumption | ≤ 1500 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link | |
| IO-Link revision | 1.1 | |
| Device profile | Identification and Diagnosis - I&D | |
| Process data | Input: 16 Bit - measurement value 8 Bit - selected threshold set 2 Bit - switching signals 3 Bit Output: 8 Bit - threshold set 2 Bit - disable transducer 1 Bit |
|
| Vendor ID | 1 (0x0001) | |
| Device ID | 3148292 (0x300A04) | |
| Transfer rate | COM1 (4.8 kbits/s) | |
| Min. cycle time | 22.4 ms | |
| SIO mode support | yes | |
| Compatible master port type | Class A (use adapter cable listed in accesories) Class B (use 3-pole adapter or 3-wire cable) |
|
| Input/Output 1 | ||
| Designation | SYNC | |
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output rated operating current | current source < 2.5 mA | |
| Pulse length | 0.4 ... 6 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 140 Hz | |
| Multiplex operation | ≤ 140 Hz /n, n = number of sensors , n ≤ 10 | |
| Input/Output 2 | ||
| Designation | IN2/FEEDBACK | |
| Input/output type | input or output programmable via IO-Link : input for selection of a threshold set (factory default) output as feedback output |
|
| Input type | digital input | |
| Signal | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
| Input impedance | ≥ 60 kΩ | |
| Pulse length | ≥ 100 ms | |
| Output type | PNP | |
| Rated operating current | 8 mA | |
| Voltage drop | < 3 V | |
| Fusing | reverse polarity protected , overload and short-circuit protected | |
| Input | ||
| Designation | IN1/TEACH | |
| Input type | 0-level: 0 ... + 1V 1-level: +UB - 1 V ... +UB |
|
| Pulse length | ≥ 100 ms | |
| Impedance | ≥ 60 kΩ | |
| Output | ||
| Designation | OUT 1 ... 3 | |
| Number | 3 | |
| Output function | OUT 1: single sheet detected OUT 2: double sheet detected OUT 3: no sheet detected (air) |
|
| Output type | Push-pull (4 in 1) output , NC contact ( programmable ) | |
| Rated operating current | 100 mA per output | |
| Voltage drop | ≤ 3 V | |
| Switch-on delay | 30 ms (programmable) | |
| Switch-off delay | 30 ms (programmable) | |
| Pulse extension | can be activated (100 ms or IO-Link cycle time) | |
| Fusing | reverse polarity protected , overload and short-circuit resistant | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9 / IO-Link V1.1.3 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 60 °C (32 ... 140 °F) | |
| Storage temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Housing length | ||
| Ultrasonic transmitter | 56 mm | |
| Ultrasonic receiver | 78 mm | |
| Housing diameter | ||
| Ultrasonic transmitter | 30 mm | |
| Ultrasonic receiver | 30 mm | |
| Degree of protection | IP65 | |
| Material | ||
| Housing | Stainless steel 1.4305/AISI 303, polyamide plastic parts | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Connector | ||
| Threading | M12 x 1 | |
| Number of pins | 8 | |
| Cable | ||
| Cable diameter | 4.3 mm | |
| Bending radius | 5 x diameter , fixed installation | |
| Material | PUR | |
| Color | black | |
| Length | approx. 200 mm | |
| Mass | 300 g | |
| Tightening torque, fastening screws | max. 30 Nm | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272801 |
| ECLASS 12.0 | 27272801 |
| ECLASS 11.0 | 27272801 |
| ECLASS 10.0.1 | 27272801 |
| ECLASS 9.0 | 27272801 |
| ECLASS 8.0 | 27272801 |
| ECLASS 5.1 | 27272801 |
| ETIM 9.0 | EC001847 |
| ETIM 8.0 | EC001847 |
| ETIM 7.0 | EC001847 |
| ETIM 6.0 | EC001847 |
| ETIM 5.0 | EC001847 |
| UNSPSC 12.1 | 41111960 |
Details: UDCM-30GS-3EP1-IO-0,2M-V19
Product Documentation: UDCM-30GS-3EP1-IO-0,2M-V19
| Brief Instructions | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|
| Commissioning instruction for series UDC-/UDCM-30GS-* / Inbetriebnahmeanleitung für Serie UDC-/UDCM-30GS-* | ALL | 419 KB | |
| Safety and Security Documentation | |||
| Návod k poużití | CZE | 147 KB | |
| Manuals | |||
| Manual UDC-/UDCM-*GS-*-IO*-Series Parameterization of Ultrasonic Double Sheet Sensors with IO-Link Interface | ENG | 4602 KB | |
| Parameter Information | |||
| IO-Link Parameter Datasheet UDCM-30GS-3EP1-IO-0,2M-V19 | ENG | 582 KB | |
Design / Simulation: UDCM-30GS-3EP1-IO-0,2M-V19
| CAD | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 6723 KB |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 73 KB |
Approvals: UDCM-30GS-3EP1-IO-0,2M-V19
| Certificates | Číslo certifikátu | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140156-4 / UL-CA-2133660-4 | ALL | 284 KB | |
| IO-Link Manufacturer Declaration | CERT-6560 | ALL | 290 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-6787 | ALL | 33 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-6788 | ALL | 31 KB | |
Software: UDCM-30GS-3EP1-IO-0,2M-V19
| Device Description Files/Drivers | Informace o uvolnění | Typ souboru | Velikost souboru |
|---|---|---|---|
| IODD for UDCM-30GS-3EP1 / IODD für UDCM-30GS-3EP1 | V1.00.000 / 2022-03-30 | ZIP | 242 KB |
| DTM (Device Type Manager) Package for UDC-18GS*/UDC-30GS* ultrasonic sensors / DTM (Device Type Manager) Package für UDC-18GS*/UDC-30GS* Ultraschallsensoren | V1.1.0.0 / 08-08-2022 | ZIP | 16847 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
Související produkty: UDCM-30GS-3EP1-IO-0,2M-V19
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
Společnost Pepperl+Fuchs vám nabízí různé dokumenty ke stažení, které obsahují poznatky o ultrazvukových senzorech.
Pepperl+Fuchs s.r.o.
Pod Vodárenskou věží 4
18208 Praha 8
Czech Republic
info@cz.pepperl-fuchs.com
+420 225 989 180
© 2024 Všechna práva vyhrazena
Pepperl+Fuchs je přední vývojář a výrobce průmyslových senzorů a komponentů pro světový trh automatizace. Neustálé inovace, trvalé kvalitní a stálý růst zaručuje mnoho úspěchů přes více než 70 let. Pepperl+Fuchs zaměstnává 6300 lidí po celém světě a má výrobní závody v Německu, USA, Singapuru, Maďarsku, Indonésii a Vietnamu, které podléhají ISO 9001.