Ultrasonic sensor UC250-F77-IU-IO-0,2M-V1
- IO-Link interface for parameterization
- Programmable via DTM with PACTWARE
- Selectable sound lobe width
- Cable with M12 plug
- Synchronization options
- Temperature compensation
- Analog output
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
PDF 파일로 된 데이타 시트 다운로드:
데이타 시트 발췌: 기술 사양 UC250-F77-IU-IO-0,2M-V1
| 제품 설명 |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 20 ... 250 mm | |
| Adjustment range | 25 ... 250 mm | |
| Dead band | 0 ... 20 mm | |
| Standard target plate | 10 mm x 10 mm | |
| Transducer frequency | approx. 400 kHz | |
| Response delay | minimum : 8 ms factory setting: 29 ms |
|
| Sensor cycle time | ≥ 8 ms (factory setting) ; programmable to 60 s |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: programming of the limits, object detected |
|
| LED red | solid: fault flashing: programming limits, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 18 ... 30 V DC , ripple 10 %SS |
|
| No-load supply current | ≤ 50 mA | |
| Power consumption | ≤ 500 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link (available after activation via programming button until next reset) | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 141 Hz | |
| Multiplex operation | ≤ 141 Hz / n , n = number of sensors , n ≤ 10 |
|
| Output | ||
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Load impedance | current output: ≤ 500 Ohm voltage output: ≥ 1000 Ohm |
|
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Polycarbonate | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Connector | ||
| Threading | M12 | |
| Number of pins | 4 | |
| Cable | ||
| Length | 200 mm | |
| Installation position | any position | |
| Mass | 20.5 g | |
| Tightening torque, fastening screws | max. 0.2 Nm | |
| Dimensions | ||
| Height | 31 mm | |
| Width | 12 mm | |
| Length | 23 mm | |
| Factory settings | ||
| Output | near limit: 25 mm far limit: 250 mm Output mode: rising ramp output type: 4 ... 20 mA |
|
| Beam width | wide | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC250-F77-IU-IO-0,2M-V1
Product Documentation: UC250-F77-IU-IO-0,2M-V1
| Brief Instructions | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|
| Commissioning instruction for UC*-F77*-IU* / Inbetriebnahmeanleitung für UC*-F77*-IU* | ALL | 440 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 150 KB | |
Design / Simulation: UC250-F77-IU-IO-0,2M-V1
| CAD | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 998 KB |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 66 KB |
Approvals: UC250-F77-IU-IO-0,2M-V1
| Certificates | 인증서 번호 | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140030-0 / UL-CA-2133555-0 | ALL | 546 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-5777 | ALL | 36 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-5778 | ALL | 41 KB | |
관련문서: UC250-F77-IU-IO-0,2M-V1
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
The USi-safety ultrasonic sensor system is breaking new ground for safety applications—whether in challenging, dusty environments or in outdoor areas.
페펄앤드푹스코리아(주)
서울특별시 서초구 서초대로88
6층 (유니온빌딩)
06673 대한민국
대한민국
info@kr.pepperl-fuchs.com
+82 2 34819494
© 2024 All Rights Reserved.
Pepperl+Fuchs는 세계 자동화 시장에서 전자기 센서 및 컴포넌트 제조 및 개발의 선두주자입니다. 지속적인 혁신, 오래토록 변치 않는 품질 및 꾸준한 성장이 지난 70년 동안 계속적인 성장을 보장하였습니다. Pepperl+Fuchs의 전세계에 6,300명의 임직원을 보유하고 있으며, 독일, USA, 싱가포르, 헝가리, 인도네시아 및 베트남에 제조 시설을 가지고 있으며, 대부분 ISO9001을 획득하였습니다.