Ultrasonic sensor UC500-18GS-IUEP-IO-V15
- IO-Link Interface for process data, parameterization and diagnosis
- Programmable via DTM with PACTWARE
- Programmable via IrDA (infrared interface)
- Selectable sound lobe width
- Synchronization options
- Enhanced temperature compensation adjustable, stable measuring values already 2 min after switching on
- Push-pull output
- Analog output
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
PDF 파일로 된 데이타 시트 다운로드:
데이타 시트 발췌: 기술 사양 UC500-18GS-IUEP-IO-V15
| 제품 설명 |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 30 ... 500 mm | |
| Adjustment range | 50 ... 500 mm | |
| Dead band | 0 ... 30 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 300 kHz | |
| Response delay | minimum : 20 ms factory setting: 40 ms |
|
| Sensor cycle time | ≥ 10 ms (factory setting) ; programmable to 60 s |
|
| Temperature influence | with temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: switch point programming, object detected |
|
| LED red | solid: error flashing: switch point programming, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 60 mA | |
| Power consumption | ≤ 1000 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface 1 | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Smart Sensor Profile 2 | |
| Process data width | 32 bit | |
| Device ID | 0x300602 (3147266) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 3 ms | |
| SIO mode support | yes | |
| Compatible master port type | Class A Class B (use 3-pole adapter or 3-wire cable) |
|
| Interface 2 | ||
| Interface type | IrDA (infrared interface) | |
| Mode | point-to-point connection | |
| Transfer rate | 115.2 kBit/s | |
| Maximum communication distance | 5 cm | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 100 Hz | |
| Multiplex operation | ≤ 71 Hz / n , n = number of sensors , n ≤ 10 | |
| Switching output | ||
| Output type | 1 push-pull output , short-circuit protected , reverse polarity protected | |
| Rated operating current | 100 mA , short-circuit/overload protected | |
| Switching frequency | factory setting: 14 Hz programmable to 33 Hz |
|
| Voltage drop | ≤ 2.5 V | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm | |
| Off-state current | ≤ 100 µA | |
| Analog output | ||
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Load resistor | current output: ≤ 500 Ω voltage output: ≥ 1000 Ω |
|
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 5-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | stainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Installation position | any position | |
| Mass | 45 g | |
| Tightening torque, fastening screws | max. 30 Nm | |
| Dimensions | ||
| Length | 90 mm | |
| Diameter | 18 mm | |
| Factory settings | ||
| Output 1 | near switch point: 50 mm far switch point: 500 mm Output mode: Window mode output behavior: NO contact |
|
| Output 2 | near limit: 50 mm far limit: 500 mm Output mode: rising ramp output behavior: Current output 4 mA ... 20 mA |
|
| Beam width | wide | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC500-18GS-IUEP-IO-V15
Informative Literature: UC500-18GS-IUEP-IO-V15
Product Documentation: UC500-18GS-IUEP-IO-V15
| Product information | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Brief Instructions | |||
| Commissioning Instruction UC*-18GS-IUEP-IO-V15 / Inbetriebnahmeanleitung UC*-18GS-IUEP-IO-V15 | ALL | 526 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 150 KB | |
| Manuals | |||
| Manual UC***-18GS Series Parameterization of Ultrasonic Sensors with IO-Link Interface | ENG | 4179 KB | |
| Parameter Information | |||
| Brief instructions | ENG | 735 KB | |
Design / Simulation: UC500-18GS-IUEP-IO-V15
| CAD | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 3759 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | ALL | EDZ | 28 KB |
Approvals: UC500-18GS-IUEP-IO-V15
| Certificates | 인증서 번호 | 언어 | 파일 타입 | 파일 크기 |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140156-4 / UL-CA-2133660-4 | ALL | 284 KB | |
| IO-Link Manufacturer Declaration | CERT-5878 | ALL | 140 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | DOC-4903A | ALL | 81 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | DOC-5211A | ALL | 74 KB | |
Software: UC500-18GS-IUEP-IO-V15
| Device Description Files/Drivers | Release Info | 파일 타입 | 파일 크기 |
|---|---|---|---|
| IODD file for UC-18GS series / IODD Datei fuer UC-18GS Serie | V1.00.000 / 2020-10-30 | ZIP | 337 KB |
| DTM (Device Type Manager) Package for UC*-18GS* ultrasonic sensors / DTM (Device Type Manager) Package für UC*-18GS* Ultraschallsensoren | V1.1.0.1 / 30-09-2022 | ZIP | 12286 KB |
| DTM (Device Type Manager) Package for UC-PROG-IR-USB Programming Device / DTM (Device Type Manager) Package für UC-PROG-IR-USB Programmieradapter | V1.1.0.1 / 31-10-2023 | ZIP | 9022 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
| Pepperl+Fuchs PACTware Connection Wizard (Add-In for PACTware) / Pepperl+Fuchs PACTware Connection Wizard (Add-In für PACTware) | 10/2020 | ZIP | 320 KB |
관련문서: UC500-18GS-IUEP-IO-V15
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
The USi-safety ultrasonic sensor system is breaking new ground for safety applications—whether in challenging, dusty environments or in outdoor areas.
페펄앤드푹스코리아(주)
서울특별시 서초구 서초대로88
6층 (유니온빌딩)
06673 대한민국
대한민국
info@kr.pepperl-fuchs.com
+82 2 34819494
© 2024 All Rights Reserved.
Pepperl+Fuchs는 세계 자동화 시장에서 전자기 센서 및 컴포넌트 제조 및 개발의 선두주자입니다. 지속적인 혁신, 오래토록 변치 않는 품질 및 꾸준한 성장이 지난 70년 동안 계속적인 성장을 보장하였습니다. Pepperl+Fuchs의 전세계에 6,300명의 임직원을 보유하고 있으며, 독일, USA, 싱가포르, 헝가리, 인도네시아 및 베트남에 제조 시설을 가지고 있으며, 대부분 ISO9001을 획득하였습니다.