Com Unit for MODBUS TCP FB8211*

Interface between the I/O modules and the PCS/PLC
Communication via MODBUS TCP
Installation in suitable enclosures in Zone 1
Module can be exchanged under voltage (hot swap)
Com unit for 80 analog or 184 digital channels
HART communication via MODBUS TCP
Configuration via FDT 1.2 DTM
Non-volatile memory for configuration and parameter settings
Self configuration in redundant systems
Permanently self-monitoring
Outputs drive to safe state in case of failures

Technical Data
Informative Literature
Product Documentation
Approvals
Software
관련문서
전문가 상담

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

PDF 파일로 된 데이타 시트 다운로드:

데이타 시트 발췌: 기술 사양 FB8211*

제품 설명
Com Unit for MODBUS TCP

Supply
Connection		backplane bus
Rated voltage		5 V DC , only in connection with the power supplies FB92**
Power consumption		2.5 W
Fieldbus connection
Fieldbus type		MODBUS TCP
Ethernet Interface
Connection type		wired to Ex e terminals via backplane
Transfer rate		10 MBit/s
Station connection		directly to PCS or PLC or via hubs or switches
Bus length		max. 100 m (Ethernet standard)
Addressing		IP address assigned via Ethernet
Ethernet address		IP V4 address (factory standard setting: 0.0.0.0, auto IP, DHCP)
Number of channels per station		max. 80 analog, max. 184 digital
Supported I/O modules		all FB remote I/O modules
HART communication		via Ethernet
Internal bus
Connection		backplane bus
Redundancy		via left front connector
Service interface
Connection		via right front connector in connection with service adapter SERV8001
Indicators/settings
LED indication		LED green (power supply): On = operating, fast flash = cold start LED red (collective alarm): On = internal fault, flashing = no Modbus TCP connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation; flashing 2 (7:1 ratio) = active, simulation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1
Conformity
Electromagnetic compatibility		NE 21
Degree of protection		IEC 60529
Fieldbus standard		IEEE 802.3
Environmental test		EN 60068-2-14
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Damaging gas		EN 60068-2-42
Relative humidity		EN 60068-2-56
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		95 % non-condensing
Shock resistance		shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Vibration resistance		frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance
Damaging gas		designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protection		IP20 (module) , a separate housing is required acc. to the system description
Connection		via backplane
Mass		approx. 750 g
Dimensions		57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Data for application in connection with hazardous areas
EU-Type Examination Certificate		PTB 97 ATEX 1074 U
	Marking	II 2 G Ex d [ib] IIC Gb
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006
International approvals
EAC approval		Russia: RU C-IT.MIII06.B.00129
Marine approval
	Lloyd Register	15/20021
	DNV GL Marine	TAA0000034
	American Bureau of Shipping	T1450280/UN
General information
System information		The module has to be mounted in appropriate backplanes (FB92**) in Zone 1, 2, or outside hazardous areas. Observe the corresponding EC-type examination certificate.
Supplementary information		EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210121
ECLASS 12.0	27210121
ECLASS 11.0	27210121
ECLASS 10.0.1	27210121
ECLASS 9.0	27210121
ECLASS 8.0	27210121
ECLASS 5.1	27210121
ETIM 9.0	EC001485
ETIM 8.0	EC001485
ETIM 7.0	EC001485
ETIM 6.0	EC001485
ETIM 5.0	EC001485
UNSPSC 12.1	39121008

Details: FB8211*

Informative Literature: FB8211*

Literature	언어	파일 타입	파일 크기
Application Report - Communication Redundancy for Uninterrupted Operation	ENG	PDF	529 KB
Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices	ENG	PDF	208 KB
Application Report - Space Saving Extension for Existing Plants	ENG	PDF	300 KB
Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants	ENG	PDF	371 KB

Product Documentation: FB8211*

System Descriptions	언어	파일 타입	파일 크기
Supported I/O modules	ENG	PDF	31 KB
Safety and Security Documentation
Instruction manual	ENG	PDF	65 KB
Manuals
Manual - FB-Remote-I/O-System	ENG	PDF	5670 KB
Manual for LB8107/FB8207, LB8111/FB8211 com unit for MODBUS RTU/TCP	ENG	PDF	6849 KB
Software Information
Software Product Note Remote I/O DTM / Softwareproduktschein Remote I/O DTM	ALL	PDF	256 KB

Approvals: FB8211*

Certificates	인증서 번호	언어	파일 타입	파일 크기
Bureau Veritas (Maritime) Marine	22449/C0 BV	ALL	PDF	590 KB
DNV Marine	TAA0000034	ALL	PDF	110 KB
United Kingdom CML UK-Type Examination Certificate UKEX Category (1) D UKEX Category (1) G UKEX Category (M1)	CML 23UKEX2147U	ALL	PDF	242 KB
Declaration of Conformity
EU Declaration of Conformity (P+F)	TDOC-1908FENG	ENG	PDF	1142 KB

Software: FB8211*

Device Description Files/Drivers	Release Info	파일 타입	파일 크기
DTM MODBUS-TCP Comm. / DTM MODBUS-TCP Comm.	Vers. 2.08pf	ZIP	19528 KB
Software Tools
LB/FB Remote I/O DTM Version 6.8.1 / LB/FB Remote I/O DTM Version 6.8.1	Version 6.8.1.	ZIP	40682 KB