Ultrasonic sensor UC800-F77S-EP-IO-1,5M-V1-P003
- IO-Link interface for service and process data
- Programmable via DTM with PACTWARE
- Continuous distance value via IO-Link process data
- Selectable sound lobe width
- Synchronization options
- Temperature compensation
- Push-pull output
- Cable with M12 plug
- Customer-specific configuration
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
De complete datasheet als PDF downloaden:
Technische gegevens UC800-F77S-EP-IO-1,5M-V1-P003
| Productbeschrijving |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 60 ... 800 mm | |
| Adjustment range | 70 ... 800 mm | |
| Dead band | 0 ... 60 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 255 kHz | |
| Response delay | minimum : 13 ms factory setting: 49 ms |
|
| Sensor cycle time | ≥ 13 ms (factory setting) ; programmable to 60 s |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: switch point programming, object detected |
|
| LED red | solid: error flashing: switch point programming, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 40 mA | |
| Power consumption | ≤ 400 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Smart Sensor | |
| Device ID | 0x300306 (3146502) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2.3 ms | |
| Process data width | 16 bit | |
| SIO mode support | yes | |
| Compatible master port type | A | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 82 Hz | |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10 |
|
| Output | ||
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected | |
| Rated operating current | 100 mA , short-circuit/overload protected | |
| Voltage drop | ≤ 2.5 V | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Switching frequency | factory setting: 12 Hz programmable max. 27 Hz | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm | |
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) When fixing with one M18 nut, the temperature range begins with 0 °C (32 °F). |
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | fixed cable with plug | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Polycarbonate | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Connector | ||
| Threading | M12 | |
| Number of pins | 4 | |
| Cable | ||
| Length | 1500 mm | |
| Installation position | any position | |
| Mass | 40 g | |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm with M18 nuts max. 1 Nm |
|
| Dimensions | ||
| Height | 31 mm | |
| Width | 21 mm | |
| Length | 23 mm | |
| Factory settings | ||
| Output | Switching point 139 mm Output mode: retroreflective mode output behavior: Normally closed (NC) |
|
| Beam width | narrow | |
| Evaluation procedure | averaging (MxN) M = 8 N = 3 |
|
| Average value | ||
| General information | ||
| Scope of delivery | 2 nuts plastic | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC800-F77S-EP-IO-1,5M-V1-P003
Informative Literature: UC800-F77S-EP-IO-1,5M-V1-P003
| Literature | Taal | Bestandstype | Bestandsgrootte |
|---|---|---|---|
| Application Report - Ultrasonic sensors measure roll diameter and detect web break | ENG | 172 KB |
Product Documentation: UC800-F77S-EP-IO-1,5M-V1-P003
| Product information | Taal | Bestandstype | Bestandsgrootte |
|---|---|---|---|
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Brief Instructions | |||
| Commissioning instruction for UC*-F77*-IU* / Inbetriebnahmeanleitung für UC*-F77*-IU* | ALL | 440 KB | |
| Manuals | |||
| Manual UC***-F77 Series Parameterization of Ultrasonic Sensors with IO-Link Interface | ENG | 4224 KB | |
Approvals: UC800-F77S-EP-IO-1,5M-V1-P003
| Certificates | Certificaatnummer | Taal | Bestandstype | Bestandsgrootte |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-US-2140030-0 / UL-CA-2133555-0 | ALL | 546 KB | |
| IO-Link Manufacturer Declaration | CERT-4363 | ALL | 254 KB |
Software: UC800-F77S-EP-IO-1,5M-V1-P003
| Device Description Files/Drivers | Vrijgave-informatie | Bestandstype | Bestandsgrootte |
|---|---|---|---|
| IODD for UC800-F77S-EP*-P002 / IODD für UC800-F77S-EP*-P002 | V1.00.001 / 2022-07-10 | ZIP | 200 KB |
| DTM (Device Type Manager) Package for UC*-F77* ultrasonic sensors / DTM (Device Type Manager) Package für UC*-F77* Ultraschallsensoren | V1.2.0.5 / 11-09-2024 | ZIP | 11923 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
Aanverwante producten: UC800-F77S-EP-IO-1,5M-V1-P003
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
The USi-safety ultrasonic sensor system is breaking new ground for safety applications—whether in challenging, dusty environments or in outdoor areas.
Pepperl+Fuchs N.V.
Metropoolstraat 11
2900 Schoten / Anvers
BELGIË
BTW BE 0436.097.152, RPR Antwerpen, afd. Antw.
sales@be.pepperl-fuchs.com
+32 3 644 25 00
© 2024 Alle rechten voorbehouden.
Pepperl+Fuchs is een toonaangevend ontwikkelaar en producent van elektronische sensoren en componenten voor de wereldwijde automatiseringsmarkt. Continue innovatie, hoge kwaliteit en gestage groei zijn de basis van ons succes, al meer dan 70 jaar. Pepperl+Fuchs heeft wereldwijd 6300 medewerkers en productiefaciliteiten in Duitsland, de Verenigde Staten, Singapore, Hongarije, Indonesië en Vietnam, waarvan het merendeel ISO 9001 gecertificeerd.