| General specifications |
| Design / Mounting | Motherboard based |
| Installation in hazardous area | Zone 2 / Div. 2 |
| Supply |
| Rated voltage | 19.2 ... 35 V DC SELV/PELV |
| Rated current | 210 ... 120 mA |
| Power dissipation | max. 4.2 W |
| Fieldbus connection |
| Number of segments | 4 |
| Fieldbus type | FOUNDATION Fieldbus |
| Physical layer profile | profile type 114 |
| ITK version | 6 |
| Implementation | resource block 1x RS
function block 4x MDI, 1x MDO, 1x MAI, 1x DI
transducer block 16x ADM TB, 1x IO TB |
| Firmware update | Ethernet |
| Polarity | polarity-sensitive |
| Rated voltage | 9 ... 35 V |
| Rated current | 0 mA |
| Ethernet Interface |
| Rated voltage | max. 35 V SELV/PELV |
| Port | 100 BASE-TX |
| Protocol | TCP/IP and UDP/IP |
| Services | ICMP , DHCP , AutoIP , HTTP |
| Connection type | RJ-45 socket, 8-pin |
| Transfer rate | 100 MBit/s |
| Diagnostic Bus |
| Connection | only for the connection to protected circuits |
| Rated voltage | max. 35 V |
| Number of Diagnostic Bus Channels | 2 |
| Number of Diagnostic Modules/Channel | 31 Using Ethernet Interface , 8 Using Fieldbus Interface |
| Termination | integrated |
| Cable length/Channel | 30 m |
| Indicators/operating means |
| LED ERR | red: Hardware fault |
| LED PWR | green: Power on |
| Fault signal | buzzer on |
| LINK/ACT | yellow |
| CH1, CH2 | yellow: diagnostic bus activity |
| Inputs |
| Input I, II | |
| Input type | selectable: Frequency input , NAMUR/mechanical contact |
| Frequency | |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Input frequency | 0.3 Hz to 1 kHz |
| Pulse duration | min. 50 µs |
| Accuracy | ± 1 % |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short-circuit |
| NAMUR | |
| Sensor type | NAMUR sensor according to IEC/EN 60947-5-6 |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Switching frequency | 10 Hz |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| Input III, IV | |
| Input type | NAMUR/mechanical contact |
| NAMUR | |
| Sensor type | NAMUR sensor according to IEC/EN 60947-5-6 |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Switching frequency | 10 Hz |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| Input V | |
| Input type | selectable: diagnostic bus CH 1 alarm input , NAMUR/mechanical contact |
| Alarm Input | |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| NAMUR | |
| Sensor type | NAMUR sensor according to IEC/EN 60947-5-6 |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Switching frequency | 10 Hz |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| Input VI | |
| Input type | selectable: diagnostic bus CH 2 alarm input , NAMUR/mechanical contact |
| Alarm Input | |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short-circuit |
| NAMUR | |
| Sensor type | NAMUR sensor according to IEC/EN 60947-5-6 |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Switching frequency | 10 Hz |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| Input VII, VIII | |
| Input type | selectable: Pt100 4-wire temperature input , NAMUR/mechanical contact |
| Temperature | |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Measuring range | -50 ... 90 °C (-58 ... 194 °F) |
| Accuracy | 1 K |
| Measuring current | 1 mA |
| Lead resistance | 4.2 Ω per line |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short-circuit |
| NAMUR | |
| Sensor type | NAMUR sensor according to IEC/EN 60947-5-6 |
| Connection | only passive load |
| Rated voltage | max. 35 V |
| Switching frequency | 10 Hz |
| Cable length | max. 30 m |
| Line fault detection | lead breakage , short circuit |
| Humidity | |
| Measuring range | 0 ... 95 % RH |
| Accuracy | 2 % RH |
| Resolution | 0.04 % |
| Outputs |
| Output I | |
| Output type | selectable: diagnostic bus CH 1 , relay , NO contact |
| Contact loading | 250 V AC/ 6 A resistive load |
| Mechanical life | 1 x 105 switching cycles |
| Response time | turn-on time 7 ms , turn-off time 3 ms |
| Switching frequency | 6 min-1 full load, 1200 min-1 without load |
| Output II | |
| Output type | selectable: diagnostic bus CH 2 , relay , NO contact |
| Contact loading | 250 V AC/ 6 A resistive load |
| Mechanical life | 1 x 105 switching cycles |
| Response time | turn-on time 7 ms , turn-off time 3 ms |
| Switching frequency | 6 min-1 full load, 1200 min-1 without load |
| Output III | |
| Output type | selectable: common alarm , volt-free contact , NC contact |
| Connection | only for the connection to protected circuits |
| Voltage | 50 V DC |
| Current | max. 1 A |
| Output IV | |
| Output type | common alarm , buzzer |
| Galvanic isolation |
| All circuits/FE | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Output I, II/other circuits | functional insulation acc. to IEC 62103, rated insulation voltage 250 Veff |
| Ethernet/Supply | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Ethernet/other circuits | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Fieldbus/other circuits | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Diagnostic Bus/other circuits | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Directive conformity |
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 |
| Low voltage | |
| Directive 73/23/EEC | EN 61010-1:2010 |
| Standard conformity |
| Galvanic isolation | IEC 62103 |
| Electromagnetic compatibility | NE 21 |
| Degree of protection | IEC 60529 |
| Fieldbus standard | IEC 61158-2 |
| Climatic conditions | DIN IEC 721 |
| Shock resistance | EN 60068-2-27 |
| Vibration resistance | EN 60068-2-6 |
| Ethernet | IEEE 802.3 |
| Ambient conditions |
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) hazardous area
-40 ... 70 °C (-40 ... 158 °F) safe area horizontal DIN rail mounting
|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
| Relative humidity | < 95 % non-condensing |
| Shock resistance | 5 g 11 ms |
| Vibration resistance | 1 g , 10 ... 150 Hz |
| Pollution degree | max. 2, according to IEC 60664 |
| Corrosion resistance | acc. to ISA-S71.04-1985, severity level G3 |
| Mechanical specifications |
| Connection type | screw terminal , pluggable |
| Housing material | Polycarbonate |
| Degree of protection | IP20 |
| Mass | 500 g |
| Dimensions | |
| Height | see dimensions |
| Width | see dimensions |
| Depth | see dimensions |
| Mounting | DIN rail mounting |
| Data for application in connection with hazardous areas |
| FOUNDATION Fieldbus | |
| Connection | For connection to circuits with safe limited voltage according to IEC 60079-11:2011, type of protection "ic" |
| Voltage Ui | max. 35 V |
| Certificate | TÜV 14 ATEX 115980 X |
| Marking | Motherboard MB-FB-GT.AD.FF.IO  II 3 G Ex nA nC IIC T4 Gc , Gateway II 3 G Ex nA IIC T4 Gc |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
| IECEx approval | IECEx TUN 14.0003X |
| Approved for | Motherboard Ex nA nC IIC T4 Gc , Gateway Ex nA IIC T4 Gc |
| General information |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
+32 3 644 25 00