HART Loop Converter KFD2-HLC-Ex1.D.2W

1-channel isolated barrier
24 V DC supply (Power Rail)
HART field device input with transmitter power supply
Usable as signal splitter (1 input and several outputs)
2 relay contact outputs (change-over contacts)
3 analog outputs 4 mA ... 20 mA
Sink and source mode output
Configurable by keypad

Technical Data
Details
Informative Literature
Product Documentation
Design / Simulation
Approvals
Software
Associated Products
Ask an Expert

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

A teljes adatlap letöltése PDF formátumban:

Adatlap kivonata: Műszaki adatok KFD2-HLC-Ex1.D.2W

General specifications
Signal type		Analog input
Supply
Connection		Power Rail or terminals 23+, 24-
Rated voltage		19 ... 30 V DC
Rated current		approx. 130 mA at 24 V DC
Power dissipation		2.5 W
Power consumption		3.1 W
HART signal channels (intrinsically safe)
Conformity		HART field device input (revision 5 to 7)
Interface
Programming interface		programming socket
Input
Connection side		field side
Connection		terminals 1, 2, 3, 4, 5, 6
Open circuit voltage/short-circuit current		typ. 24 V / 28 mA
Input resistance		250 Ω , 5 % (terminals 2, 3 and with jumper on 5, 6)
Available voltage		≥ 15.5 V at 20 mA, short-circuit protected
Output
Connection side		control side
Connection		output I: terminals 10, 11, 12, output II: terminals 16, 17, 18 output III: terminals 7, 8, 9, output IV: terminals 13, 14, 15, output V: terminals 19, 20, 21
Output I, II
	Output signal	relay and LED yellow
	Mechanical life	10⁷ switching cycles
	Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Output III, IV, V
	Output signal	analog
	Current range	4 ... 20 mA , (source or sink mode)
	Load	max. 650 Ω , source mode
	Voltage range	5 ... 30 V , sink mode from external supply
	Fault signal	downscale I ≤ 2 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43) or hold measurement value
Other outputs		HART communicator on terminals 22, 24
Collective error message		Power Rail and LED red
Transfer characteristics
Output III, IV, V
	Resolution	max. 2 µA
	Accuracy	< 20 µA, 10 µA typ.
	Influence of ambient temperature	< ± 2 µA/K
	Duration of measurement/Response delay	HART message acquisition time plus 100 ms
Relay		programmable either for fault or trip value (with direction, hysteresis and delay)
Galvanic isolation
Output I/II		functional insulation acc. to IEC 62103, rated insulation voltage 250 V_eff
Output I, II/other circuits		reinforced insulation acc. to IEC 62103, rated insulation voltage 300 V_rms
Output III/IV/V/power supply		functional insulation acc. to IEC 62103, rated insulation voltage 50 V_eff
Indicators/settings
Display elements		LEDs , display
Control elements		Control panel
Configuration		via operating buttons via PACTware
Labeling		space for labeling at the front
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Conformity
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529:2001
Ambient conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection		IP20
Connection		screw terminals
Mass		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
	Height	119 mm
	Width	40 mm
	Depth	115 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
EU-type examination certificate		BASEEFA 07 ATEX 0174
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC
Supply
	Maximum safe voltage	253 V AC (Attention! The rated voltage can be lower.)
Equipment		terminals 1, 4/3 (with link between terminals 4 and 5)
	Voltage	25.2 V
	Current	104.9 mA
	Power	0.661 W
	Internal capacitance	1.1 nF
	Internal inductance	0 mH
Equipment		terminals 2, 5/3
	Voltage	< 28 V
	Power	< 1.33 W
	Voltage	1.1 V
	Current	11.9 mA
	Power	4 mW
	Internal capacitance	0 µF
	Internal inductance	0 mH
Output I, II		terminals 10, 11, 12; 16, 17, 18 , non-intrinsically safe
	Maximum safe voltage	253 V (Attention! U_m is no rated voltage.)
	Contact loading	253 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (BASEEFA 07 ATEX 0174) 50 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (Pepperl+Fuchs self-declaration)
Output III, IV, V		terminals 7, 8, 9; 13, 14, 15; 19, 20, 21 , non-intrinsically safe
	Maximum safe voltage	253 V (Attention! U_m is no rated voltage.)
Certificate		PF 07 CERT 1141 X
	Marking	II 3G Ex nA nC IIC T4 Gc
Galvanic isolation
	Input/Other circuits	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
FM approval
	Control drawing	116-0129
IECEx approval
	IECEx certificate	IECEx BAS 07.0047
	IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27210190
ECLASS 12.0	27210190
ECLASS 11.0	27210190
ECLASS 10.0.1	27210190
ECLASS 9.0	27210190
ECLASS 8.0	27210190
ECLASS 5.1	27242692
ETIM 9.0	EC001601
ETIM 8.0	EC001601
ETIM 7.0	EC001601
ETIM 6.0	EC001601
ETIM 5.0	EC001597
UNSPSC 12.1	39121008

Details: KFD2-HLC-Ex1.D.2W

Function

This isolated barrier is used for intrinsic safety applications. It is a HART loop converter that provides power to transmitters or can be connected to existing HART loops in parallel.

It is able to evaluate up to four HART variables (PV, SV, TV, QV). Of those four HART variables, the data contained in any three of them can be converted to three different 4 mA ... 20 mA current signals. These loop signals can be connected to display devices or analog inputs on the process control system/ control system.

In addition to the current outputs, two form C changeover relay contacts are available and can be programmed to operate at trip values from the HART variables.

The unit is easily programmed by the use of a keypad located on the front of the unit or with the PACTware™ configuration software.

For additional information, refer to the manual and www.pepperl-fuchs.com.

Informative Literature: KFD2-HLC-Ex1.D.2W

Literature	Nyelv	Fájltípus	Fájlméret
Application Report - Biological Cleaning of Wastwater and Secondary Sedimentation Stage	ENG	PDF	566 KB
Application Report - Energy Generation in Wastwater Treatment Plants	ENG	PDF	532 KB
Application Report - Generating Electricity in Coal-Fired Power Plants	ENG	PDF	412 KB
Application Report - Sand Trap and Preliminary Sedimentation Stage	ENG	PDF	448 KB
Application Report - Screening Systems in Sewage Treatment Plants	ENG	PDF	577 KB
Application Report - Sicherer Brennstofftransport in Kohlekraftwerken	ENG	PDF	391 KB
Application Report - Water Inlet in Wastewater Treatment Plants	ENG	PDF	526 KB

Product Documentation: KFD2-HLC-Ex1.D.2W

Brief Instructions	Nyelv	Fájltípus	Fájlméret
Operator card KF-HLC-1.D* / Bedienkarte KF-HLC-1.D*	ALL	PDF	981 KB
Safety and Security Documentation
Használati útmutató	HUN	PDF	167 KB
Manuals
Manual KF-HLC-1.D*	ENG	PDF	4267 KB
Manual	ENG	PDF	3685 KB

Design / Simulation: KFD2-HLC-Ex1.D.2W

CAD	Nyelv	Fájltípus	Fájlméret
CAD 3-D / CAD 3-D	ALL	STP	2722 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN Data Portal / CAE EPLAN Data Portal	ALL	LINK	---
EPLAN macro EDZ / EPLAN Makro EDZ	ALL	EDZ	87 KB

Approvals: KFD2-HLC-Ex1.D.2W

Certificates	Tanúsítvány sz.	Nyelv	Fájltípus	Fájlméret
Baseefa IECEx Certificate of Conformity	IECEx BAS 07.0047	ALL	LINK	---
Brasil TUV Rheinland Brazil	TÜV 13.2090	ALL	PDF	1210 KB
Canada FM	FM22CA0014X	ALL	PDF	317 KB
China SITIIAS CCC Ex Certificate	2021322316004122 (Singapore)	ALL	PDF	1359 KB
Europe Baseefa ATEX Category (1) G ATEX Category (1) D	Baseefa 07 ATEX 0174	ALL	PDF	3311 KB
Europe Pepperl+Fuchs Certificate of Compliance ATEX Category 3 G ATEX Category 3	PF 07 CERT 1141X	ALL	PDF	227 KB
South Africa MASC	MASC S/17-0873	ALL	PDF	701 KB
USA FM	CoC 3032427	ALL	PDF	84 KB
United Kingdom UK-Type Examination Certificate UKEX Category (1) G UKEX Category (1) D	CML 21UKEX21103	ALL	PDF	198 KB
Control Drawings
Control drawing FM / Control drawing FM		ALL	PDF	58 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-0646D	ALL	PDF	83 KB

Software: KFD2-HLC-Ex1.D.2W

Device Description Files/Drivers	Megjelenési információ	Fájltípus	Fájlméret
DTM Collection HART Loop Converter / DTM Collection HART Loop Converter	1.0.6.0	ZIP	13857 KB
Software Tools
PACTware 4.1 SP6 / PACTware 4.1 SP6	4.1.0.53	ZIP	43327 KB
PACTware 5.0 / PACTware 5.0	5.0.5.31	ZIP	44203 KB

Kapcsolódó termékek: KFD2-HLC-Ex1.D.2W

Matching System Components

	KFD2-EB2 Power Feed Module
	Interface for Power Rail, Supply current ≤ 4 A, Replaceable fuse, Relay contact output, reversible, LED status indicationpa

	UPR-03 Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 2 m (6 foot), simple to customize to application space, Eliminates daisy-chainspa

	UPR-03-S Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 0.8 m (2.6 ft), simple to customize to application space, Eliminates daisy-chainspa

	DTM HART Loop converter DTM collection
	Device DTM, For HART Loop Converters, Frame application, like e. g. PACTware, must be installed separatelypa

	PACTware 5.0 FDT Framework
	Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa

	K-ADP-USB Adapter with USB Interface
	Isolated USB interface cable, Used with K-, E- and H-System devices, Used with PACTwarepa

	UPR-03-M Universal Power Rail
	35 mm DIN mounting rail with 3-conductor insert, Provides DC supply voltage to all equipped K-System modules, Standard length 1.6 m (5 foot), simple to customize to application space, Eliminates daisy-chainspa

	K-DUCT-BU Profile Rail
	Cable trunking is integrated in the mounting profile, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Standard length 1.8 m (5.8 ft), simple to customize to application space, With mounting aidspa

	K-DUCT-BU-UPR-03 Profile Rail
	Cable trunking with integrated Power Rail UPR-03, Safe spacious separation of safe and hazardous signals, No additional cable guides necessary, Provides DC supply voltage to all equipped K-System modules, Standard length 1.8 m (5.8 ft), simple to customize to application space, With end caps UPR-E, cover and mounting aidspa

Accessories

	K-250R Measuring resistor
	1-channel, Precision resistor, Conversion of 0 mA ... 20 mA/0 V ... 5 Vpa

	K-500R0%1 Measuring resistor
	1-channel, Precision resistor, Conversion of 4 mA ... 20 mA/2 V ... 10 Vpa

	KF-ST-5GN Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces greenpa

	KF-ST-5BU Terminal Block
	3-pin screw terminal, For KF modules of K-System, Packaging unit: 5 pieces bluepa

	KF-CP Coding Pins
	Coding of K-System terminal blocks, Coding of LB/FB-System front sockets, Packaging unit: 20 x 6 coding pinspa

General Notes Relating to Pepperl+Fuchs Product Information

Gyorshivatkozások

Selector for Safety Products

Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.

Pepperl+Fuchs Kereskedelmi Kft.
8200 Veszprém
Kistó utca 16 - 18.
Magyarország
sales@hu.pepperl-fuchs.com
phone +36 88 545 902

A Pepperl+Fuchs az elektronikai érzékelők és alkatrészek vezető fejlesztő és gyártó vállalata a globális automatizálási piacon. A folyamatos innováció, a tartós minőség és az állandó növekedés már több mint 70 éve garantálja a sikert. A Pepperl+Fuchs 6300 embert alkalmaz világszerte, gyártóegységei vannak Németországban, az USA-ban, Szingapúrban, Magyarországon, Indonéziában és Vietnámban, legtöbbjük ISO 9001 tanusítvánnyal is rendelkezik.