IO-Link motor control module ICA-8IO-4M4-G20-IO-P14
- Configuration and control via IO-Link
- Connections for 24 V or 48 V DC roller motors
- Inputs for 2- and 3-wire sensors
- Electronic PNP outputs
- Function indicator for motors, inputs and outputs
- Mounting directly in the support profile
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Stáhněte si kompletní katalogový list ve formátu PDF:
Výňatek z katalogového listu: Technická data ICA-8IO-4M4-G20-IO-P14
| Popis produktu |
|---|
| G20 IO-Link module for digital inputs/outputs, 8 inputs and 8 outputs, 4 connections for roller motors with 24 V or 48 V |
| General specifications | ||
|---|---|---|
| MTBF | 90 a | |
| Compatible roller motors | Interroll EC310, Interroll EC5000 24V/48V AI (20W / 35W / 50W), Interroll EC5000 48V AI (20W / 35W / 50W), Rulmeca BL3, Itoh Denki PM500XK, Itoh Denki PM500XC , PULSEROLLER Senergy-IDC | |
| Indicators/operating means | ||
| LED yellow/red | IO1 ... IO8: IN, OUT, IO-Link status M1 ... M4: motor status |
|
| Electrical specifications | ||
| Auxiliary voltage | 18 ... 56 V DC PELV Max. 10 A Current limitation of the supply max. 30 A For UL: Z-type miniature circuit breaker in accordance with UL 1077, max. 20 A, required |
|
| Operating voltage | 18 ... 30 V DC, PELV Current limitation of the supply max. 4 A |
|
| No-load supply current | ≤ 25 mA | |
| Operating current | max. 2.5 A | |
| Interface | ||
| Interface type | IO-Link | |
| IO-Link revision | 1.1 | |
| Device profile | Identification and Diagnosis - I&D | |
| Process data | 8 byte inputs (STD/EXT) 6 byte outputs (STD) 18 byte outputs (EXT) |
|
| Vendor ID | 1 (0x0001) | |
| Device ID | 984068 (0x0F0404) (STD) - default 984067 (0x0F0403) (EXT) |
|
| Data transfer rate | COM3 (230.4 kbits/s) | |
| Min. cycle time | 1.2 ms (STD) 2 ms (EXT) |
|
| SIO mode support | no | |
| Compatible master port type | Class A |
|
| Input | ||
| Number/Type | 8 Inputs for 3-wire sensors (PNP), DC (IO1 ... IO8) | |
| Supply | from IO-Link | |
| Current loading capacity | 200 mA per connection IO1/2 ... IO7/8 , overload and short-circuit protected | |
| Input current | ≤ 5 mA (limited internally) | |
| Switching point | Type 3 according to IEC 61131-2 | |
| Output 1 | ||
| Number/Type | 8 electronic outputs, PNP (IO1 … IO8), overload proof and short-circuit proof | |
| Supply | from IO-Link | |
| Current | 200 mA per output | |
| Voltage | ≥ (Ue - 1.5 V) | |
| Output 2 | ||
| Number/Type | 4 outputs for DC roller motors (MOT1 ... MOT4) | |
| Supply | via UPWR | |
| Current loading capacity | 3.5 A (continuous), 5 A (< 2 s), max. 7.5 A (< 0.3 s) per motor Total current (continuous) max. 10 A per device (TB ≤ 50 °C) max. 6 A per device (TB ≤ 70 °C) |
|
| Overload protection | Fuse 4 A, I2t = 122.5 A2s per motor | |
| Signal level | Speed: US = 0.3 … 10 V in no-load operation Ri = 5.6 kΩ, RLOAD ≥ 35 kΩ Direction of rotation: Digital output PNP UD low = high resistance UD high ≥ 12 V Ri = 5.6 kΩ, RLOAD ≥ 15 kΩ |
|
| Fault level | Motor fault: Digital input NPN 0 (no error) ≥ 125 µA 1 (error) ≤ 25 µA |
|
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 EN 55011:2016 |
|
| Standard conformity | ||
| Degree of protection | EN 60529:2000 | |
| Fieldbus standard | EN 61131-9:2013 | |
| Input | EN 61131-2:2007 | |
| Communication interface | IEC 61131-9 / IO-Link V1.1.3 | |
| Emitted interference | EN 61000-6-4:2007 | |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006 | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Relative humidity | 85 % non-condensing | |
| Climatic conditions | For indoor use only | |
| Altitude | ≤ 5000 m above MSL | |
| Shock and impact resistance | 30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks | |
| Vibration resistance | 0.35 mm / 5 g 5 ... 500 Hz | |
| Pollution degree | 2 | |
| Mechanical specifications | ||
| Degree of protection | IP54 according to EN 60529 | |
| Connection | 24 V/48 V power (PWR): Piercing technology, black or gray flat cable IO-Link: M12 round plug connector in accordance with EN 61076-2-101, LM type (4-pin, connector contacts, screw-locking, A-coded) Female connector: LF type or similar Inputs/outputs (IO), motors (MOT): M8 round plug connector in accordance with EN 61076-2-104 IO: LF type (4-pin, bushing contacts, screw-locking, A-coded) Female connector: LM type or similar MOT: NF type (5-pin, bushing contacts, snap-locking, B-coded) Female connector: NM type or similar |
|
| Mass | 390 g | |
| Dimensions | ||
| Height | 27.5 mm | |
| Width | 131.5 mm | |
| Length | 54 mm | |
| Mounting | 2 clips with ∅ 8 mm drill hole The module must be secured to a solid, continuous surface using the two lugs |
|
| Cable length | 1 m (IO-Link) 1.5 m (IO1/2, IO7/8), 0.8 m (IO3/4, IO5/6) 1.0 m (MOT1, MOT4); 0.4 m (MOT2, MOT3) max. 10 m |
|
| Note | The flat cable routing is designed for 100 actuation cycles | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27242602 |
| ECLASS 12.0 | 27242602 |
| ECLASS 11.0 | 27242602 |
| ECLASS 10.0.1 | 27242602 |
| ECLASS 9.0 | 27242602 |
| ECLASS 8.0 | 27242602 |
| ECLASS 5.1 | 27242602 |
| ETIM 9.0 | EC001597 |
| ETIM 8.0 | EC001597 |
| ETIM 7.0 | EC001597 |
| ETIM 6.0 | EC001597 |
| ETIM 5.0 | EC001597 |
| UNSPSC 12.1 | 32151705 |
Details: ICA-8IO-4M4-G20-IO-P14
Product Documentation: ICA-8IO-4M4-G20-IO-P14
| Brief Instructions | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|
| Instruction leaflet / Beipackzettel | ALL | 206 KB | |
| Manuals | |||
| Manual | ENG | 766 KB | |
| Parameter Information | |||
| IODD for ICA-8IO-4M4-G20-IO-P14 (EXT) | ENG | 512 KB | |
| IODD for ICA-8IO-4M4-G20-IO-P14 (STD) | ENG | 510 KB | |
Approvals: ICA-8IO-4M4-G20-IO-P14
| Certificates | Číslo certifikátu | Jazyk | Typ souboru | Velikost souboru |
|---|---|---|---|---|
| IO-Link Manufacturer Declaration | CERT-7376 | ALL | 173 KB | |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) | TDOC-7569_CZE | CZE | 196 KB | |
| UK Declaration of Conformity (P+F) | TDOC-7571_ENG | ENG | 171 KB | |
Software: ICA-8IO-4M4-G20-IO-P14
| Device Description Files/Drivers | Informace o uvolnění | Typ souboru | Velikost souboru |
|---|---|---|---|
| IODD for ICA-8IO-4M4-G20-IO-P14 (EXT) / IODD für ICA-8IO-4M4-G20-IO-P14 (EXT) | V1.00.000 / 2024-04-10 | ZIP | 223 KB |
| IODD for ICA-8IO-4M4-G20-IO-P14 (STD) / IODD für ICA-8IO-4M4-G20-IO-P14 (STD) | V1.00.000 / 2024-04-10 | ZIP | 222 KB |
| Software Tools | |||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
Související produkty: ICA-8IO-4M4-G20-IO-P14
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
Připojte senzory ve výrobních prostorech ke cloudu a začněte digitální transformaci s novými úvodními sadami IIoT.
Pepperl+Fuchs s.r.o.
Pod Vodárenskou věží 4
18208 Praha 8
Czech Republic
info@cz.pepperl-fuchs.com
+420 225 989 180
© 2024 Všechna práva vyhrazena
Pepperl+Fuchs je přední vývojář a výrobce průmyslových senzorů a komponentů pro světový trh automatizace. Neustálé inovace, trvalé kvalitní a stálý růst zaručuje mnoho úspěchů přes více než 70 let. Pepperl+Fuchs zaměstnává 6300 lidí po celém světě a má výrobní závody v Německu, USA, Singapuru, Maďarsku, Indonésii a Vietnamu, které podléhají ISO 9001.