Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
A teljes adatlap letöltése PDF formátumban:
Supply | ||
---|---|---|
Connection | backplane bus | |
Rated voltage | 5 V DC , only in connection with the power supplies FB92** | |
Power consumption | 2 W | |
Interface | ||
Connection | HDLC via terminals on backplane | |
Station connection | directly to PCS | |
Bus length | max. 150 m (500 feet) | |
Internal bus | ||
Connection | backplane bus | |
Service interface | ||
Connection | 8-pin connector to be used in case of maintenance via safety barrier |
|
Indicators/settings | ||
LED indication | LED green: supply LED red: fault LED yellow: communication status |
|
Labeling | space for labeling at the front | |
Directive conformity | ||
Electromagnetic compatibility | ||
Directive 2014/30/EU | EN 61326-1 | |
Conformity | ||
Electromagnetic compatibility | NE 21 | |
Degree of protection | IEC 60529 | |
Fieldbus standard | HDLC via terminals on backplane | |
Environmental test | HDLC to ISO 13239 | |
Shock resistance | EN 60068-2-27 | |
Vibration resistance | EN 60068-2-6 | |
Damaging gas | EN 60068-2-42 | |
Relative humidity | EN 60068-2-56 | |
Ambient conditions | ||
Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) , 70 °C (non-Ex) | |
Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
Relative humidity | 95 % non-condensing | |
Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
Damaging gas | for plugs: 21 days in 25 ppm SO2, at 25 °C and 75 % rel. humidity, device G3 | |
Mechanical specifications | ||
Degree of protection | IP20 (module) , mounted on backplane | |
Connection | device plug (accessories) front connector for letterbug and service bus |
|
Mass | 150 g | |
Dimensions | 32 x 100 x 103 mm (1.26 x 3.9 x 4 inch) | |
Height | 100 mm | |
Width | 32 mm | |
Length | 103 mm | |
Data for application in connection with hazardous areas | ||
Supply | only in connection with the power supplies LB9*** | |
Certificate | PF 08 CERT 1234 | |
Marking | II 3 G Ex nA IIC T4 | |
Directive conformity | ||
Directive 2014/34/EU | EN 60079-0 , EN 60079-1 , EN 60079-11 | |
International approvals | ||
UL approval | QUZW7.E106378 | |
IECEx approval | BVS 08.0011X | |
General information | ||
System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure. |
|
Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
System | Classcode |
---|---|
ECLASS 13.0 | 27210121 |
ECLASS 12.0 | 27210121 |
ECLASS 11.0 | 27210121 |
ECLASS 10.0.1 | 27210121 |
ECLASS 9.0 | 27210121 |
ECLASS 8.0 | 27210121 |
ECLASS 5.1 | 27210121 |
ETIM 9.0 | EC001485 |
ETIM 8.0 | EC001485 |
ETIM 7.0 | EC001485 |
ETIM 6.0 | EC001485 |
ETIM 5.0 | EC001485 |
UNSPSC 12.1 | 39121008 |
The ISCM Remote I/O ComUnit or gateway brings intrinsically safe inputs and outputs from sensors and actuators to the Foxboro Invensys HDLC bus.
It makes use of all the regular I/O modules and thus transports signals to and from NAMUR and switch type inputs and high power IS solenoids or even power relays. The system supplies 4 mA to 20 mA transmitters and accepts input from 20 mA current sources or temperature sensors. It drives I/P converters and proportional valves and positioners.
The HDLC hardware is familiar to Invensys I/A series users. Autoconfiguration ensures that modules register with the host as soon as they are inserted. There is no extra configuration required.
The system makes use of regular I/A series function blocks behaving like any ordinary FBM.
Certificates | Tanúsítvány sz. | Nyelv | Fájltípus | Fájlméret |
---|---|---|---|---|
DEKRA EXAM IECEx Certificate of Conformity | IECEx BVS 09.0037X | ALL | LINK | --- |
DNV Marine | TAA0000034 | ALL | 110 KB | |
Lloyd's Register Marine | LR2003616TA-02 | ALL | 557 KB | |
South Africa MASC | MASC MS/20-8438X | ALL | 730 KB |
Accessories | ||||||
---|---|---|---|---|---|---|
|