Inductive positioning system PMI120-F90-C2EP-IO-V15-3G-3D
- Parameterization and diagnosis via IO-Link
- Measuring range 0 ... 120 mm
- Parameterisable measuring range
- Analog current or voltage output, programmable
- 2 Push-pull outputs
- Switch points programmable via IO-Link
请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。
下载PDF版完整参数表:
技术参数节选 PMI120-F90-C2EP-IO-V15-3G-3D
| General specifications | ||
|---|---|---|
| Switching element function | Analog current or voltage output, programmable 2 switch outputs, programmable |
|
| Object distance | 0.5 ... 3 mm , recommended: 1.5 mm | |
| Measuring range | 0 ... 120 mm | |
| Linearity range | 1 ... 119 mm | |
| Nominal ratings | ||
| Operating voltage | 12 ... 30 V DC (13 ... 30 V when analog voltage output is parameterized) |
|
| Reverse polarity protection | reverse polarity protected | |
| Linearity error | within measuring range: ± 0.8 mm within linearity range: ± 0.4 mm |
|
| Repeat accuracy | ± 0.1 mm | |
| Resolution | 50 µm | |
| Temperature drift | ± 0.5 mm (-25 °C ... 70 °C) | |
| No-load supply current | ≤ 40 mA | |
| Operating voltage indicator | LED green | |
| Functional safety related parameters | ||
| MTTFd | 278 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Indicators/operating means | ||
| LED S1 | switching state Switching output 1 | |
| LED S2 | switching state Switching output 2 | |
| LED S3 | Damping element in the configured analog measuring range | |
| LED STATUS | Status display LED, green/red (Power on, communication/error, missing damping element) | |
| Interface | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Smart Sensor | |
| Device ID | 0x200404 (2098180) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Value range | 0000h ... 9600h | |
| Min. cycle time | 2.3 ms | |
| Process data width | Process data input: 16 Bit Process data output: none |
|
| SIO mode support | yes | |
| Compatible master port type | A | |
| Switching output | ||
| Output type | 2 push-pull outputs (can be parameterized), short-circuit-proof, reverse polarity protection, surge-proof | |
| Operating current | ≤ 100 mA / Output | |
| Switching window | ± 1 mm | |
| Switching hysteresis | 0.2 mm | |
| Voltage drop | ≤ 3 V | |
| Short-circuit protection | pulsing | |
| Analog output | ||
| Output type | 1 current output: 4 ... 20 mA or 1 voltage output: 0 ... 10 V , programmable | |
| Load resistor | current output: ≤ 400 Ω voltage output: ≥ 1000 Ω |
|
| Short-circuit protection | voltage output: current limit | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 EN 60947-5-7:2003 EN61131-9:2013 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source, Type 1 enclosure | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | 5-pin, M12 x 1 connector | |
| Degree of protection | IP67 / IP69K | |
| Material | ||
| Housing | PBT, stainless steel 1.4571 , brass, nickel-plated | |
| Target | mild steel, e. g. 1.0037, SR235JR (formerly St37-2) | |
| Mass | 113 g | |
| Dimensions | ||
| Height | 40 mm | |
| Width | 23 mm | |
| Length | 135.2 mm | |
| Data for application in connection with hazardous areas | ||
| Equipment protection level | Gc (nA) , Dc | |
| Equipment protection level Gc (nA) | ||
| Type of protection | "n" | |
| CE marking | [*PD-Z02586A*] | |
| Certificates | ||
| ATEX certificate | PF 15 CERT 3754 X | |
| ATEX marking |  II 3G Ex nA IIC T6 Gc |
|
| Standards | EN 60079-0:2012+A11:2013 , EN 60079-15:2010 |
|
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output voltage UAmax , maximum analog output current IAmax | |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. mode of operation 1 at UBmax = 30 V and maximum 2 switching outputs with each ILmax =100 mA and 1 analog output with IAmax = 20mA or UAmax = 10 V : 35 °C (95 °F) mode of operation 2 at UBmax = 30 V and maximum 1 switching output with ILmax =100 mA : 50 °C (122 °F) |
|
| Equipment protection level Dc | ||
| Type of protection | Protection by enclosure "tc" | |
| CE marking | [*PD-Z02586A*] | |
| Certificates | ||
| ATEX certificate | PF 15 CERT 3774 X | |
| ATEX marking | II 3D Ex tc IIIC T80°C Dc |
|
| Standards | EN 60079-0:2012/A11+2013 , EN 60079-31:2014 | |
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output voltage UAmax , maximum analog output current IAmax | |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. mode of operation 1 at UBmax = 30 V and maximum 2 switching outputs with each ILmax =100 mA and 1 analog output with IAmax = 20mA or UAmax = 10 V : 35 °C (95 °F) mode of operation 2 at UBmax = 30 V and maximum 1 switching output with ILmax =100 mA : 50 °C (122 °F) |
|
| General information | ||
| Use in the hazardous area | see instruction manuals | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27274004 |
| ECLASS 12.0 | 27274004 |
| ECLASS 11.0 | 27270702 |
| ECLASS 10.0.1 | 27270702 |
| ECLASS 9.0 | 27270702 |
| ECLASS 8.0 | 27270702 |
| ECLASS 5.1 | 27270702 |
| ETIM 9.0 | EC001852 |
| ETIM 8.0 | EC001852 |
| ETIM 7.0 | EC001852 |
| ETIM 6.0 | EC001852 |
| ETIM 5.0 | EC001852 |
| UNSPSC 12.1 | 39121550 |
| Product category / 产品类的 |
Details: PMI120-F90-C2EP-IO-V15-3G-3D
Product Documentation: PMI120-F90-C2EP-IO-V15-3G-3D
| Product information | 语言 | 文件类型 | 文件大小 |
|---|---|---|---|
| Installation and Design Notes for Position Sensors, F90 Series | ENG | 311 KB | |
| Installation and user instructions for offline parameterization of IO-Link sensors | ENG | 1788 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 169 KB | |
Approvals: PMI120-F90-C2EP-IO-V15-3G-3D
| Certificates | 证书号码 | 语言 | 文件类型 | 文件大小 |
|---|---|---|---|---|
| Canada USA UL Ordinary Location | UL-CA-2133562-0 / UL-US-2140037-0 | ALL | 546 KB | |
| Europe Pepperl+Fuchs ATEX Category 3 D Certificate | PF15CERT3774X | ALL | 1001 KB | |
| Europe Pepperl+Fuchs ATEX Category 3 G Certificate | PF15CERT3754X | ALL | 1015 KB |
Software: PMI120-F90-C2EP-IO-V15-3G-3D
| Software Tools | Release Info | 文件类型 | 文件大小 |
|---|---|---|---|
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | V1.00.006 / 2022-07-10 | ZIP | 96138 KB |
配套产品: PMI120-F90-C2EP-IO-V15-3G-3D
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
倍加福（北京）过程自动化控制设备有限公司
北京市经济技术开发区
科创十四街99号7号楼3101室
101111 Beijing
中国
pa-info@cn.pepperl-fuchs.com
+86 10 5901 7000
上海倍加福工业自动化贸易有限公司
上海市静安区市北工业园区江场三路
219号4楼
200436 上海
中国
fa-info@cn.pepperl-fuchs.com
+86 21 6630 3939
沪ICP备20009978号 | © 2024 版权所有。
德国倍加福公司（P+F）是全球自动化行业中久负盛名的专业传感器公司。倍加福作为全球自动化领域的电子传感与零部件的生产主导者，凭借不断的创新，恒久的质量保证，稳健的发展，保证了迄今六十余年的辉煌成就。倍加福在全球范围内拥有6300名员工，位于德国，美国，新加坡，匈牙利，印度尼西亚和越南的生产基地几乎全部通过了ISO9001的质量认证。