Assistance gamme Détecteurs industriels
Tél.: +33 1 60 92 13 13
Fax : +33 1 60 92 13 25
Support en ligne pour la protection contre le risque d’explosion
Tél.: +33 1 60 92 13 14
Fax: +33 1 60 92 13 25
Digital Input FB1308B3
- 8-channel
- Inputs with plug-in Ex e terminals
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- Dry contact or NAMUR inputs
- Positive or negative logic selectable
- Simulation mode for service operations (forcing)
- Line fault detection (LFD)
- Permanently self-monitoring
- On/Off delay
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Téléchargez ici la fiche technique complète en PDF:
Caractéristiques techniques FB1308B3
| Slots | ||
|---|---|---|
| Occupied slots | 2 | |
| Supply | ||
| Connection | backplane bus | |
| Rated voltage | 12 V DC , only in connection with the power supplies FB92** | |
| Power dissipation | 0.95 W | |
| Power consumption | 0.95 W | |
| Internal bus | ||
| Connection | backplane bus | |
| Interface | manufacturer-specific bus to standard com unit | |
| Digital input | ||
| Number of channels | 8 | |
| Sensor interface | ||
| Connection | NAMUR sensor | |
| Connection [2] | volt-free contact | |
| Connection [3] | active binary signal 24 V DC | |
| Connection | channel I: 1+, 2-; channel II: 3+, 4-; channel III: 5+, 6-; channel IV: 7+, 8-; channel V: 9+, 10-; channel VI: 11+, 12-; channel VII: 13+, 14-; channel VIII: 15+, 16- | |
| Rated values | acc. to EN 60947-5-6 (NAMUR) | |
| Switching point/switching hysteresis | 1.2 ... 2.1 mA / ± 0.2 mA | |
| Internal resistor | 1 kΩ | |
| Line fault detection | can be switched on/off for each channel via configuration tool , active signals (24 V, 5 V) without line fault detection | |
| Connection | mechanical switch with additional resistors (see connection diagram) proximity sensors without additional wiring | |
| Short-circuit | < 360 Ω | |
| Open-circuit | < 0.35 mA | |
| Digital signals (active) | configurable 24 V 5 V | |
| Switching point: ON | > 8 V > 2.7 V | |
| Switching point: OFF | < 3 V < 2.3 V | |
| Minimum pulse duration | 1 ms | |
| Indicators/settings | ||
| LED indication | LED green: supply LED red: line fault , red flashing: communication error |
|
| Coding | optional mechanical coding via front socket | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 | |
| Conformity | ||
| Degree of protection | IEC 60529:2000 | |
| Environmental test | EN 60068-2-14:2009 | |
| Shock resistance | EN 60068-2-27:2009 | |
| Vibration resistance | EN 60068-2-6:2008 | |
| Damaging gas | EN 60068-2-42:2003 | |
| Relative humidity | EN 60068-2-78:2001 | |
| Ambient conditions | ||
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| Mechanical specifications | ||
| Degree of protection | IP20 (module) , a separate housing is required acc. to the system description | |
| Connection | Ex e spring terminal with protective cover | |
| Mass | approx. 750 g | |
| Dimensions | 57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch) | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | FIDI 21 ATEX 0012 U | |
| Marking |  II 2G Ex db eb q IIC Gb |
|
| Galvanic isolation | ||
| Input/power supply, internal bus | safe electrical isolation acc. to EN 60079-11:2007 , voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2018 EN 60079-1:2014 EN 60079-5:2015 EN 60079-7:2015+A1:2018 |
|
| International approvals | ||
| ATEX approval | FIDI 21 ATEX 0012 U | |
| IECEx approval | ||
| IECEx certificate | IECEx FIDI 21.0002U | |
| IECEx marking | Ex db eb q IIC Gb | |
| General information | ||
| System information | The module has to be mounted in appropriate backplanes (FB92**) in Zone 1, 2, or outside hazardous areas. Observe the corresponding EC-type examination certificate. | |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210121 |
| ECLASS 12.0 | 27210121 |
| ECLASS 11.0 | 27210121 |
| ECLASS 10.0.1 | 27210121 |
| ECLASS 9.0 | 27210121 |
| ECLASS 8.0 | 27210121 |
| ECLASS 5.1 | 27210120 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: FB1308B3
Informative Literature: FB1308B3
| Literature | Langue | Type de fichier | Taille |
|---|---|---|---|
| Application Report - Communication Redundancy for Uninterrupted Operation | ENG | 529 KB | |
| Application Report - LB and FB Remote I/O Systems for Digitally Connecting Analog Field Devices | ENG | 208 KB | |
| Application Report - Space Saving Extension for Existing Plants | ENG | 300 KB | |
| Application Report - Using Remote I/O Systems for the Efficient Digitalization of Plants | ENG | 371 KB |
Product Documentation: FB1308B3
| Safety and Security Documentation | Langue | Type de fichier | Taille |
|---|---|---|---|
| Manuel d'instructions | FRA | 154 KB | |
| Manuals | |||
| Hardware Manual FB-Remote-I/O-System | ENG | 9157 KB | |
Design / Simulation: FB1308B3
| CAD | Langue | Type de fichier | Taille |
|---|---|---|---|
| CAD 3-D / CAD 3-D | ALL | STP | 7330 KB |
| CAD Portal / CAD Portal | ALL | LINK | --- |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| EPLAN macro EDZ / EPLAN Makro EDZ | ALL | EDZ | 2205 KB |
Approvals: FB1308B3
| Certificates | Identification | Langue | Type de fichier | Taille |
|---|---|---|---|---|
| Europe Fiditas ATEX Category 2 G | FIDI 21 ATEX 0012U | ALL | 1163 KB | |
| Fiditas IECEx Certificate of Conformity | IECEx FIDI 21.0002U | ALL | LINK | --- |
| Declaration of Conformity | ||||
| EU Declaration of Conformity (P+F) | TDOC-5037BFRA | FRA | 1139 KB | |
- Demandez à un Expert
- Demande pour une référence équivalente
- Suivi de votre commande en cours
- Nouveautés
- Service Level Agreements for ecom instruments
- Où commander
- Sélection de documentations
- Technologies
- Solutions systèmes de contrôle
- Recherche de documents techniques, catalogues ou brochures
- Articles de presse
- Salons internationaux
- Salons et événements - France
Pepperl+Fuchs Eurl
12 Avenue des Tropiques
91955 Courtaboeuf Cedex
France
info@fr.pepperl-fuchs.com
+33 1 60921300
© 2024 Tous droits réservés.
Pepperl+Fuchs est leader comme concepteur et fabricant de capteurs et composants électroniques pour le marché mondial de l'automatisation. L'innovation constante, la qualité incontestable et la croissance soutenue, garantissent notre succès, depuis plus de 70 ans. Pepperl+Fuchs emploie 6300 personnes dans le monde et compte des usines en Allemagne, aux USA, à Singapour, en Hongrie, en Indonésie et au Vietnam ; la plupart d'entre elles sont certifiées ISO 9001.