Redundancy Module PS1000-D2-24.20.RM

24 V DC to 28 V DC input
2 inputs with 1 output
Output 24 V DC, 20 A
Housing width 32 mm
Built-in decoupling mosfets for 1+1 and N+1 redundancy
Automatic load sharing
Reverse input polarity protection
Easy wiring: distribution terminal for negative pole included
Redundancy status indicator
Suitable for Zone 2/Div. 2 mounting

Technical Data
Informative Literature
Product Documentation
Design / Simulation
Approvals
配套产品
咨询专家

请注意：所有以Pepperl + Fuchs GmbH或Pepperl + Fuchs AG名义发行的产品相关文件，例如证书，合格声明等，同样适用于Pepperl + Fuchs SE。

下载PDF版完整参数表:

技术参数节选 PS1000-D2-24.20.RM

Electrical specifications
Voltage drop		input to output 0.1 ... 0.5 V at input 2 x 5 A 0.2 ... 0.5 V at input 2 x 10 A 0.24 ... 0.5 V at input 2 x 12 A load share dependent
Power dissipation		1.7 W no load 2.6 ... 4.7 W at input 2 x 5 A 5.6 ... 8.7 W at input 2 x 10 A
Input
Rated voltage		24 ... 28 V
Voltage range		18 ... 35 V DC
Current		2 x 12 A at ambient temperature < 45 °C (113 °F) 2 x 10 A at ambient temperature 70 °C (158 °F) 2x 17 mA for max. 5 s for lower output currents see technical information
Output
Voltage range		24 ... 28 V DC
Current		24 A at ambient temperature < 45 °C (113 °F) 20 A at ambient temperature < 70 °C (158 °F) 32.5 A for max. 5 s max. 26 A in overload or short circuit mode (voltage < 6 V DC)
Fault indication output
Connection		terminals 13, 14 : relay contact load share terminals 23, 24 : relay contact redundancy
Output type		relay contact load share - contact is closed if the adjustment of the output voltages are sufficient - contact is open if an even load share does not occur and readjustment of the output voltage is required relay contact redundancy - contact is closed if no fault is detected - contact is open if one or both input voltages are below 22 V DC or above 30 V DC - contact is open if the output current is higher than the adjusted value of the output current - contact is open if an internal defect of the device is detected
Contact loading		max. 60 V DC/0.3 A ; 30 V DC/1 A ; 30 V AC/0.5 A resistive load min. 1 mA at 5 V DC
Galvanic isolation
Input/Output		SELV/PELV
Indicators/settings
Display elements		LED green: output status - LED lights up if the output current is smaller than the adjusted value of the output current LEDs green: load share status - LEDs indicate the load share status between the two power supplies LED green: redundancy status - LED lights up if no fault is detected - LED flashes if one ore both input values are below 22 V or above 30 V - LED flashes if the output current is higher than the adjusted value of the output current - LED flashes if an internal defect is detected
Control elements		rotary switch
Configuration		setting of the output current via rotary switch - switch setting to 5 A in combination with two 5A power supplies (1+1 redundancy) - switch setting to 10 A in combination with two 10A power supplies (1+1 redundancy) - switch setting to 20 A for N+1 redundant systems
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	IEC/EN 61000-6-1 , IEC/EN 61000-6-2 , IEC/EN 61000-6-3 , IEC/EN 61000-6-4
Low voltage
	Directive 2014/35/EU	EN 61010-1
RoHS
	Directive 2011/65/EU (RoHS)	IEC/EN 63000:2019
Conformity
Degree of protection		EN 60529
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F) , see technical information
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		5 ... 95 %, noncondensing
Shock resistance		20 g , 11 ms or 30 g , 6 ms
Vibration resistance		2 ... 17.8 Hz : ± 1.6 mm , 17.8 ... 500 Hz : 2 g
Mechanical specifications
Housing material		aluminum alloy , galvanized steel
Degree of protection		IP20
Connection
	Input/Output	screw terminals conductor cross section: max. 6 mm² (AWG 20-10) cable diameter: max. 2.8 mm, wire end ferrules included stripped insulation length: 7 mm tightening torque: max. 0.8 Nm
	Relay contact output	spring terminals conductor cross section: max. 1.5 mm² (AWG 24-16) cable diameter: max. 1.6 mm, wire end ferrules included stripped insulation length: 7 mm
Mass		approx. 310 g
Dimensions		32 x 124 x 117 mm (W x H x D) , without DIN mounting rail
	Height	124 mm
	Width	32 mm
	Depth	117 mm
Mounting		on 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
ATEX approval
	ATEX certificate	EPS 11 ATEX 1 312 X
	ATEX marking	II 3G Ex ec nC II T4 Gc
Directive conformity
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-7:2016 , EN 60079-15:2010
International approvals
UL approval		E223176
IECEx approval
	IECEx certificate	IECEx EPS 20.0057X
	IECEx marking	Ex ec nC IIC T4 Gc
	Standards	IEC 60079-0:2011 , IEC 60079-7:2015 , IEC 60079-15:2010
General information
Supplementary information		Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

System	Classcode
ECLASS 13.0	27040790
ECLASS 12.0	27040790
ECLASS 11.0	27040790
ECLASS 10.0.1	27040790
ECLASS 9.0	27040790
ECLASS 8.0	27049090
ECLASS 5.1	27049090
ETIM 9.0	EC002542
ETIM 8.0	EC002542
ETIM 7.0	EC002542
ETIM 6.0	EC002542
ETIM 5.0	EC002542
UNSPSC 12.1	39121004
Product category / 产品类的	冗余模块

Details: PS1000-D2-24.20.RM

Informative Literature: PS1000-D2-24.20.RM

Literature	语言	文件类型	文件大小
Product Information - PS1000 for Global Use up to Zone 2/Div. 2	ENG	PDF	577 KB

Product Documentation: PS1000-D2-24.20.RM

Product information	语言	文件类型	文件大小
Technical information	ENG	PDF	3796 KB
Safety and Security Documentation
Instruction manual / Betriebsanleitung	ALL	PDF	225 KB
Instruction manual / Betriebsanleitung	ALL	PDF	294 KB

Design / Simulation: PS1000-D2-24.20.RM

CAD	语言	文件类型	文件大小
CAD 3-D / CAD 3-D	ALL	STP	4884 KB
CAD Portal / CAD Portal	ALL	LINK	---
CAE
CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ	ALL	EDZ	200 KB

Approvals: PS1000-D2-24.20.RM

Certificates	证书号码	语言	文件类型	文件大小
Bureau Veritas IECEx Certificate of Conformity	IECEx EPS 20.0057X	ALL	LINK	---
Canada, USA CSA Hazardous Location	CoC 80059967	ALL	PDF	84 KB
China SITIIAS CCC Ex Certificate	2023122303116293 (Mannheim)	ALL	PDF	519 KB
Europe Bureau Veritas ATEX Category 3 G	EPS 11 ATEX 1 312X	ALL	PDF	1011 KB
US CA UL	CoC E223176 RptRef E223176-20070416	ALL	PDF	444 KB
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)	DOC-4793	ALL	PDF	73 KB
EU Declaration of Conformity (P+F)	TDOC-4793AENG	ENG	PDF	185 KB

配套产品: PS1000-D2-24.20.RM

Accessory of

	PS1000-A6-24.10 Power Supply
	100 V AC to 240 V AC wide-range input, Output 24 V DC, 10 A, 240 W, 1-phase, Housing width 39 mm, Efficiency up to 95.2 %, Minimal inrush current surge, DC OK relay contact, Suitable for Zone 2/Div. 2 mounting, Device type: device for DIN rail mounting, Function: Standard, Rated voltage: 24 V DC, Voltage range: 24 ... 28 V DC factory setting: 24.1 Vpa

	PS1000-A6-24.5 Power Supply
	100 V AC to 240 V AC wide-range input, Output 24 V DC, 5 A, 120 W, 1-phase, Housing width 32 mm, Efficiency up to 94.3 %, Minimal inrush current surge, DC OK relay contact, Suitable for Zone 2/Div. 2 mounting, Device type: device for DIN rail mounting, Function: Standard, Rated voltage: 24 V DC, Voltage range: 24 ... 28 V DC factory setting: 24.1 Vpa

General Notes Relating to Pepperl+Fuchs Product Information

快速链接

倍加福（北京）过程自动化控制设备有限公司
北京市经济技术开发区
科创十四街99号7号楼3101室
101111 Beijing
中国
pa-info@cn.pepperl-fuchs.com
phone +86 10 5901 7000

上海倍加福工业自动化贸易有限公司
上海市静安区市北工业园区江场三路
219号4楼
200436 上海
中国
fa-info@cn.pepperl-fuchs.com
phone +86 21 6630 3939

德国倍加福公司（P+F）是全球自动化行业中久负盛名的专业传感器公司。倍加福作为全球自动化领域的电子传感与零部件的生产主导者，凭借不断的创新，恒久的质量保证，稳健的发展，保证了迄今六十余年的辉煌成就。倍加福在全球范围内拥有6300名员工，位于德国，美国，新加坡，匈牙利，印度尼西亚和越南的生产基地几乎全部通过了ISO9001的质量认证。